Knowledge Test Class B
This license is required for driving a single vehicle with a GVWR of more than 26,001 pounds, and a trailer not to exceed 10,000 pounds gross vehicle weight rating, or a vehicle designed to transport 24 or more people (including the driver). To receive this license, applicants must pass a 50-question test. To pass, applicants must answer 40 questions correctly. Each question has three or four possible answer choices. Test questions come from the Alabama Commercial Driver License Manual. Questions come from chapters covering: Introduction, Driving Safely, Transporting Cargo Safely, Air Brakes (if applicable), Pre-Trip Vehicle Inspection Test, Basic Vehicle Control Skills Test and On-Road Driving.. Endorsements that may be used with a Class B CDL are: Hazardous materials, Tank, Passenger, HazMat and Tank, Air Brakes and School bus.
Number of Question
Passing Score
15. During the driving test, the examiner will be scoring you on:
Explanation
During the on-road driving test, the examiner will be score you on specific driving maneuvers as well as on your general driving behavior. You must drive in a safe and responsible manner; obey all traffic signs, signals, and laws; and not cause an accident or commit a moving violation.
16. How do ice cream trucks become hazardous to other drivers?
Explanation
Ice cream trucks can create hazardous conditions for other drivers because they attract children. Children often do not notice or pay attention to other vehicles on the roadway when running to or from ice cream trucks.
17. If your brakes fail on a downgrade, your best hope to stop is to:
Explanation
If your brakes fail on a downgrade, you will have to look outside your vehicle for a way to stop. Using an escape ramp is the safest way to stop your vehicle.
18. You may be an aggressive driver if you:
Explanation
Avoid being an aggressive driver by being realistic about your travel time, making allowance for delays, maintaining reasonable following distances, and not making hand gestures that could anger another driver.
19. When an engine is started:
Explanation
After a vehicle is started, the warning lights and buzzers should go out after a few seconds. If the warning signals do not turn off, there may be something wrong with the vehicle.
20. Which of the following is not a good rule when using turn signals?
Explanation
When using your turn signals, you should signal well before the turn or lane change, signal continuously throughout the turn or lane change, and cancel the signal after you have completed your move.
21. Drowsy driving is most common during:
Explanation
Drowsy driving is most common during the night because people are naturally prone to be less alert in the hours during which they are normally asleep. If you must drive at night, take every precaution to prevent fatigued driving.
Ranked by best match
Frequently Asked Questions
A Class B Commercial Driver License (CDL) in Alabama allows an individual to operate a single vehicle with a GVWR (Gross Vehicle Weight Rating) of 26,001 pounds or more, or a combination of vehicles with a combined GVWR of less than 26,001 pounds. This includes vehicles such as delivery trucks, dump trucks, and buses carrying 16 or more passengers (including the driver).
To obtain a Class B CDL license in Alabama, the following steps must be taken:
1. Obtain a Commercial Learner's Permit (CLP) by passing the written knowledge test and obtaining a medical certificate from a certified medical examiner.
2. Hold the CLP for at least 14 days before taking the skills test.
3. Schedule an appointment with a certified third-party CDL examiner or visit an Alabama Department of Public Safety location to take the skills test.
4. Pass the pre-trip inspection, basic control skills, and on-road driving portions of the skills test.
5. Pay the required fees and obtain your Class B CDL license from Alabama Department of Public Safety.
It is important to note that individuals must also meet specific age requirements and have a clean driving record to obtain a Class B CDL license in Alabama.
To obtain a Class B CDL license in Alabama, the following steps must be taken:
1. Obtain a Commercial Learner's Permit (CLP) by passing the written knowledge test and obtaining a medical certificate from a certified medical examiner.
2. Hold the CLP for at least 14 days before taking the skills test.
3. Schedule an appointment with a certified third-party CDL examiner or visit an Alabama Department of Public Safety location to take the skills test.
4. Pass the pre-trip inspection, basic control skills, and on-road driving portions of the skills test.
5. Pay the required fees and obtain your Class B CDL license from Alabama Department of Public Safety.
It is important to note that individuals must also meet specific age requirements and have a clean driving record to obtain a Class B CDL license in Alabama.
With a Class B CDL license in Alabama, you are authorized to operate a single vehicle with a GVWR of 26,001 pounds or more, and/or a combination of vehicles with a combined GVWR of less than 26,001 pounds. This includes vehicles such as delivery trucks, dump trucks, and buses carrying 16 or more passengers (including the driver).
Examples of vehicles that you can operate with a Class B CDL license in Alabama include:
- Straight trucks (e.g., box trucks and dump trucks) with a GVWR of 26,001 pounds or more
- Buses with a seating capacity of 16 or more passengers (including the driver)
- Segmented buses
- Trucks towing trailers with less than 10,000 pounds GVWR
- Large passenger vans designed to transport 16 or more passengers (including the driver)
- Tow trucks with a GVWR of 26,001 pounds or more
It is important to note that certain endorsements may be required to operate certain types of vehicles, such as air brake endorsements for vehicles equipped with air brakes.
Examples of vehicles that you can operate with a Class B CDL license in Alabama include:
- Straight trucks (e.g., box trucks and dump trucks) with a GVWR of 26,001 pounds or more
- Buses with a seating capacity of 16 or more passengers (including the driver)
- Segmented buses
- Trucks towing trailers with less than 10,000 pounds GVWR
- Large passenger vans designed to transport 16 or more passengers (including the driver)
- Tow trucks with a GVWR of 26,001 pounds or more
It is important to note that certain endorsements may be required to operate certain types of vehicles, such as air brake endorsements for vehicles equipped with air brakes.
To obtain a Class B Commercial Driver License (CDL) license in Alabama, you must meet the following requirements:
1. Age: You must be at least 18 years old to obtain a Class B CDL license in Alabama. However, you can only engage in intrastate commerce (i.e., within the state of Alabama) until you turn 21 years old. To engage in interstate commerce (i.e., across state lines), you must be at least 21 years old.
2. Valid driver's license: You must have a valid, non-commercial driver's license issued by the state of Alabama.
3. Medical certification: You must obtain a medical certificate from a certified medical examiner to prove that you meet the medical standards necessary to operate commercial motor vehicles.
4. Knowledge test: You must pass a written knowledge test that covers topics such as vehicle inspection, driving safety, and hazardous materials regulations.
5. Skills test: You must pass a three-part skills test consisting of a pre-trip inspection, basic vehicle control skills, and an on-road driving test.
6. Fees: You must pay the required fees to obtain your Class B CDL license.
Additionally, you must have a clean driving record and not have any disqualifying criminal convictions or drug or alcohol violations on your record.
1. Age: You must be at least 18 years old to obtain a Class B CDL license in Alabama. However, you can only engage in intrastate commerce (i.e., within the state of Alabama) until you turn 21 years old. To engage in interstate commerce (i.e., across state lines), you must be at least 21 years old.
2. Valid driver's license: You must have a valid, non-commercial driver's license issued by the state of Alabama.
3. Medical certification: You must obtain a medical certificate from a certified medical examiner to prove that you meet the medical standards necessary to operate commercial motor vehicles.
4. Knowledge test: You must pass a written knowledge test that covers topics such as vehicle inspection, driving safety, and hazardous materials regulations.
5. Skills test: You must pass a three-part skills test consisting of a pre-trip inspection, basic vehicle control skills, and an on-road driving test.
6. Fees: You must pay the required fees to obtain your Class B CDL license.
Additionally, you must have a clean driving record and not have any disqualifying criminal convictions or drug or alcohol violations on your record.
In Alabama, the minimum age requirement for obtaining a Class B Commercial Driver License (CDL) is 18 years old. However, if you are between the ages of 18 and 21, you can only operate commercial motor vehicles within the state of Alabama (intrastate commerce).
If you want to operate commercial vehicles across state lines (interstate commerce), you must be at least 21 years old. This age requirement is set by federal regulations and applies to all states in the United States.
It's important to note that certain endorsements may also have additional age requirements. For example, to transport hazardous materials, you must be at least 21 years old in addition to holding a hazardous materials endorsement on your CDL.
If you want to operate commercial vehicles across state lines (interstate commerce), you must be at least 21 years old. This age requirement is set by federal regulations and applies to all states in the United States.
It's important to note that certain endorsements may also have additional age requirements. For example, to transport hazardous materials, you must be at least 21 years old in addition to holding a hazardous materials endorsement on your CDL.
It depends on the type of vehicle you plan to operate and the cargo you plan to transport with your Class B Commercial Driver License (CDL).
The following endorsements are available for Class B CDL holders in Alabama:
1. Passenger endorsement (P): Required for drivers who plan to operate a vehicle designed to transport 16 or more passengers, including the driver.
2. School bus endorsement (S): Required for drivers who plan to operate a school bus.
3. Tanker endorsement (N): Required for drivers who plan to transport liquids or gases in bulk containers with a capacity of 1,000 gallons or more.
4. Hazardous materials endorsement (H): Required for drivers who plan to transport hazardous materials as defined by federal law.
5. Combination of tank vehicle and hazardous materials endorsement (X): Required for drivers who plan to transport hazardous materials in tank vehicles.
To obtain any of these endorsements, you must pass additional knowledge and skills tests specific to each endorsement. Additionally, some endorsements may require additional background checks or medical certifications.
The following endorsements are available for Class B CDL holders in Alabama:
1. Passenger endorsement (P): Required for drivers who plan to operate a vehicle designed to transport 16 or more passengers, including the driver.
2. School bus endorsement (S): Required for drivers who plan to operate a school bus.
3. Tanker endorsement (N): Required for drivers who plan to transport liquids or gases in bulk containers with a capacity of 1,000 gallons or more.
4. Hazardous materials endorsement (H): Required for drivers who plan to transport hazardous materials as defined by federal law.
5. Combination of tank vehicle and hazardous materials endorsement (X): Required for drivers who plan to transport hazardous materials in tank vehicles.
To obtain any of these endorsements, you must pass additional knowledge and skills tests specific to each endorsement. Additionally, some endorsements may require additional background checks or medical certifications.
The Class B Commercial Driver License (CDL) skills test is a three-part exam that evaluates your ability to operate a commercial vehicle safely. The three parts are:
1. Pre-trip inspection: You will be tested on your ability to inspect the vehicle to ensure it is safe to operate. You will be asked to identify and explain various parts and equipment of the vehicle and demonstrate how to check them for safety.
2. Basic vehicle control: You will be tested on your ability to control the vehicle in various situations, such as backing up, turning, parking, and maneuvering through tight spaces.
3. On-road driving: You will be tested on your ability to safely operate the vehicle in normal traffic situations, including intersections, turns, lane changes, and highway driving.
During the skills test, you will be observed and evaluated by a licensed examiner who will score your performance based on a predetermined set of criteria. To pass the test, you must achieve a score of at least 80% on each part of the exam.
It's important to note that you must have a valid Alabama CDL learner's permit and meet all other eligibility requirements before taking the skills test. Additionally, you must provide a properly equipped commercial vehicle for the test.
1. Pre-trip inspection: You will be tested on your ability to inspect the vehicle to ensure it is safe to operate. You will be asked to identify and explain various parts and equipment of the vehicle and demonstrate how to check them for safety.
2. Basic vehicle control: You will be tested on your ability to control the vehicle in various situations, such as backing up, turning, parking, and maneuvering through tight spaces.
3. On-road driving: You will be tested on your ability to safely operate the vehicle in normal traffic situations, including intersections, turns, lane changes, and highway driving.
During the skills test, you will be observed and evaluated by a licensed examiner who will score your performance based on a predetermined set of criteria. To pass the test, you must achieve a score of at least 80% on each part of the exam.
It's important to note that you must have a valid Alabama CDL learner's permit and meet all other eligibility requirements before taking the skills test. Additionally, you must provide a properly equipped commercial vehicle for the test.
Yes, there are some restrictions and limitations for drivers with a Class B Commercial Driver License (CDL) in Alabama. These restrictions and limitations include:
1. No passengers: If you hold a Class B CDL with a passenger endorsement (P), you are not allowed to transport more than 15 passengers, including the driver.
2. No hazardous materials: If you hold a Class B CDL with a hazardous materials endorsement (H), you are not allowed to transport hazardous materials that require placards.
3. No combination vehicles: If you hold a Class B CDL, you are not allowed to operate combination vehicles, which are vehicles with two or more trailers or other articulated units.
4. Air brake restriction: If you do not pass the air brakes knowledge test or the air brakes skills test in a vehicle equipped with air brakes, you will be restricted from operating vehicles with air brakes.
5. Automatic transmission restriction: If you take the skills test in a vehicle with an automatic transmission, your CDL will be restricted to driving vehicles with automatic transmissions only.
It's important to note that violating these restrictions and limitations can result in fines, penalties, and even the suspension or revocation of your CDL.
1. No passengers: If you hold a Class B CDL with a passenger endorsement (P), you are not allowed to transport more than 15 passengers, including the driver.
2. No hazardous materials: If you hold a Class B CDL with a hazardous materials endorsement (H), you are not allowed to transport hazardous materials that require placards.
3. No combination vehicles: If you hold a Class B CDL, you are not allowed to operate combination vehicles, which are vehicles with two or more trailers or other articulated units.
4. Air brake restriction: If you do not pass the air brakes knowledge test or the air brakes skills test in a vehicle equipped with air brakes, you will be restricted from operating vehicles with air brakes.
5. Automatic transmission restriction: If you take the skills test in a vehicle with an automatic transmission, your CDL will be restricted to driving vehicles with automatic transmissions only.
It's important to note that violating these restrictions and limitations can result in fines, penalties, and even the suspension or revocation of your CDL.
No, the Class B Commercial Driver License (CDL) written test in Alabama is only available in English. The Alabama Department of Public Safety (DPS) requires all applicants to demonstrate a basic understanding of the English language before issuing a CDL. This is because English is the language of the road, and all road signs and signals are in English.
However, if you have difficulty reading or understanding English, you can bring an interpreter with you to translate the questions and answers on the written test. The interpreter must be at least 18 years old, fluent in both English and your preferred language, and not related to you.
It's important to note that if you pass the written test using an interpreter, your CDL will include a restriction that requires you to be accompanied by an interpreter when operating a commercial vehicle. Additionally, you must still demonstrate proficiency in English during the skills test and on-road driving test.
However, if you have difficulty reading or understanding English, you can bring an interpreter with you to translate the questions and answers on the written test. The interpreter must be at least 18 years old, fluent in both English and your preferred language, and not related to you.
It's important to note that if you pass the written test using an interpreter, your CDL will include a restriction that requires you to be accompanied by an interpreter when operating a commercial vehicle. Additionally, you must still demonstrate proficiency in English during the skills test and on-road driving test.
Yes, if you have a disability that may impact your ability to take the Class B Commercial Driver License (CDL) written test in Alabama, you may request accommodations. The Alabama Department of Public Safety (DPS) provides reasonable accommodations to ensure that all individuals have equal access to CDL testing.
To request accommodations, you should contact the DPS Driver License Division in advance of your testing appointment to discuss your needs. You will be required to provide documentation of your disability and the requested accommodation. The DPS may provide accommodations such as extended time for testing, a separate testing area, or assistive technology.
It's important to note that the DPS will consider each request for accommodations on a case-by-case basis, and not all requests may be granted. Additionally, any requested accommodations must not fundamentally alter the nature of the CDL test or give you an unfair advantage over other test-takers.
To request accommodations, you should contact the DPS Driver License Division in advance of your testing appointment to discuss your needs. You will be required to provide documentation of your disability and the requested accommodation. The DPS may provide accommodations such as extended time for testing, a separate testing area, or assistive technology.
It's important to note that the DPS will consider each request for accommodations on a case-by-case basis, and not all requests may be granted. Additionally, any requested accommodations must not fundamentally alter the nature of the CDL test or give you an unfair advantage over other test-takers.
If you fail the Class B Commercial Driver License (CDL) written test in Alabama, you will have the opportunity to retake the test, but you will need to wait at least one day before retaking the test. You will need to pay a fee each time you take the test, so it's important to make sure you are adequately prepared before taking the test.
The Alabama Department of Public Safety (DPS) allows applicants to take the written test up to three times in a 12-month period. If you fail the test three times, you must wait at least 6 months before taking the test again.
It's important to note that if you fail the written test, you will not be eligible to take the skills test or on-road driving test until you pass the written test. Therefore, it's important to study and prepare thoroughly for the written test to avoid delays in obtaining your CDL.
The Alabama Department of Public Safety (DPS) allows applicants to take the written test up to three times in a 12-month period. If you fail the test three times, you must wait at least 6 months before taking the test again.
It's important to note that if you fail the written test, you will not be eligible to take the skills test or on-road driving test until you pass the written test. Therefore, it's important to study and prepare thoroughly for the written test to avoid delays in obtaining your CDL.
