Knowledge Test Class A
This license is required for driving any legal combination of vehicles, with a gross combination weight rating of 26,001 pounds or more, provided the GVWR of a trailer exceeds 10,000 pounds To receive this license, applicants must pass a 50-question test. To pass, applicants must answer 40 questions correctly. Each question has three possible answer choices. Test questions come from the Oklahoma Commercial Driver License Manual. Questions come from chapters covering: Introduction, Driving Safely, Transporting Cargo Safely, Air Brakes (if applicable), Combination, Doubles and Hazardous Materials. Endorsements that may be used with a Class A CDL are: Hazardous materials, Tank, Passenger, HazMat and Tank, Air Brakes and School bus.
Number of Question
Passing Score
36. Which of the following is not a reason to cover cargo?
Explanation
You should cover your cargo to protect people from the cargo if it spills, as well as to protect the cargo from the weather.
37. Brakes can get out of adjustment quickly, especially:
Explanation
Brakes are particularly prone to getting out of adjustment if they are hot. Be sure to routinely check the adjustment of your brakes. For a vehicle to be safely controlled, all brakes must be properly functioning and adjusted.
38. When pulled over to the side of the road, you should:
Explanation
When stopped on the side of the road, be sure to turn on your vehicle's four-way emergency flashers, especially during times of lowered visibility. Place warning devices within 10 minutes of being stopped.
39. When you must travel down a hill, when should you switch into a lower gear?
Explanation
You should always slow down and shift into a lower gear before starting down a hill. If you do not begin to drive down a hill at a low enough speed, you risk overusing your brakes, causing them to overheat and fade.
40. One way to prevent hydroplaning on wet road surfaces is to:
Explanation
When driving on a wet road surface, the risk of hydroplaning is increased if your tire pressure is too low or your tire tread is too worn. If you begin to hydroplane, release the accelerator and push in the clutch to slow down.
41. If a worker is present in a work zone, you should:
Explanation
When driving through a work zone, follow the posted speed limits. If workers are present, you should slow to a speed that is even lower than the posted limit.
42. A distracted driver:
Explanation
Distracted drivers perceive hazards on the road more slowly than drivers who are focused, or they do not perceive hazards at all.
Ranked by best match
Frequently Asked Questions
A Class A Commercial Driver's License (CDL) is a type of license required to operate a combination of vehicles with a total weight of 26,001 pounds or more. In Oklahoma, this includes any combination of vehicles with a gross vehicle weight rating (GVWR) of 26,001 pounds or more, provided that the vehicle being towed has a GVWR of more than 10,000 pounds.
To obtain a Class A CDL license in Oklahoma, you must meet certain requirements, including passing a written knowledge test and a skills test. You must also meet specific medical and physical qualifications and provide proof of identity and residency in Oklahoma.
Additionally, you may be required to obtain endorsements on your CDL for certain types of driving, such as hazardous materials or passenger transport. These endorsements will require additional testing and training.
It is important to note that driving with a CDL comes with additional responsibilities and stricter regulations than driving with a regular driver's license. It is important to follow all traffic laws and safety guidelines to maintain your CDL license and ensure the safety of yourself and others on the road.
To obtain a Class A CDL license in Oklahoma, you must meet certain requirements, including passing a written knowledge test and a skills test. You must also meet specific medical and physical qualifications and provide proof of identity and residency in Oklahoma.
Additionally, you may be required to obtain endorsements on your CDL for certain types of driving, such as hazardous materials or passenger transport. These endorsements will require additional testing and training.
It is important to note that driving with a CDL comes with additional responsibilities and stricter regulations than driving with a regular driver's license. It is important to follow all traffic laws and safety guidelines to maintain your CDL license and ensure the safety of yourself and others on the road.
With a Class A CDL license in Oklahoma, you are authorized to operate combination vehicles with a gross vehicle weight rating (GVWR) of 26,001 pounds or more. This includes any combination of vehicles where the towed vehicle has a GVWR of more than 10,000 pounds.
Some examples of vehicles you can operate with a Class A CDL license include:
- Tractor-trailers
- Truck and trailer combinations
- Livestock carriers
- Flatbed trucks towing a trailer
- Tanker trucks towing a trailer
- Dump trucks towing a trailer
- Logging trucks towing a trailer
It is important to note that operating these types of vehicles requires additional knowledge, skills, and training beyond what is required for a regular driver's license. It is important to follow all traffic laws and safety guidelines to maintain your CDL license and ensure the safety of yourself and others on the road.
Some examples of vehicles you can operate with a Class A CDL license include:
- Tractor-trailers
- Truck and trailer combinations
- Livestock carriers
- Flatbed trucks towing a trailer
- Tanker trucks towing a trailer
- Dump trucks towing a trailer
- Logging trucks towing a trailer
It is important to note that operating these types of vehicles requires additional knowledge, skills, and training beyond what is required for a regular driver's license. It is important to follow all traffic laws and safety guidelines to maintain your CDL license and ensure the safety of yourself and others on the road.
To obtain a Class A CDL license in Oklahoma, you must meet the following requirements:
1. Be at least 18 years of age to drive within the state of Oklahoma and 21 years of age to drive interstate or transport hazardous materials.
2. Have a valid Oklahoma driver's license.
3. Provide proof of identity and residency in Oklahoma.
4. Pass a Department of Transportation (DOT) physical exam to ensure that you meet medical and physical qualifications for operating a commercial vehicle.
5. Pass a written knowledge test that covers topics such as vehicle inspection, safe driving practices, and transporting cargo.
6. Obtain a Commercial Learner's Permit (CLP) by passing the CDL general knowledge test and any endorsements required for your desired type of driving.
7. Complete behind-the-wheel training with a qualified instructor to prepare for the skills test.
8. Pass a skills test that includes a pre-trip inspection, basic control skills, and an on-road driving test.
9. Pay the required fees for obtaining your CDL license and any endorsements.
It is important to note that some types of driving require additional endorsements on your CDL, such as hazardous materials, passenger transport, or double/triple trailers. These endorsements will require additional testing and training beyond the basic Class A CDL requirements.
1. Be at least 18 years of age to drive within the state of Oklahoma and 21 years of age to drive interstate or transport hazardous materials.
2. Have a valid Oklahoma driver's license.
3. Provide proof of identity and residency in Oklahoma.
4. Pass a Department of Transportation (DOT) physical exam to ensure that you meet medical and physical qualifications for operating a commercial vehicle.
5. Pass a written knowledge test that covers topics such as vehicle inspection, safe driving practices, and transporting cargo.
6. Obtain a Commercial Learner's Permit (CLP) by passing the CDL general knowledge test and any endorsements required for your desired type of driving.
7. Complete behind-the-wheel training with a qualified instructor to prepare for the skills test.
8. Pass a skills test that includes a pre-trip inspection, basic control skills, and an on-road driving test.
9. Pay the required fees for obtaining your CDL license and any endorsements.
It is important to note that some types of driving require additional endorsements on your CDL, such as hazardous materials, passenger transport, or double/triple trailers. These endorsements will require additional testing and training beyond the basic Class A CDL requirements.
The minimum age requirement for obtaining a Class A CDL license in Oklahoma is 18 years old to drive within the state of Oklahoma. However, to drive interstate or transport hazardous materials, you must be at least 21 years old.
It is important to note that some employers may have their own age requirements that exceed the minimum legal age. Additionally, some endorsements for a CDL (such as passenger transport or hazardous materials) may also have age requirements that exceed the minimum legal age. It is important to check with your state's Department of Motor Vehicles and any potential employers to determine the specific age requirements for your desired type of driving.
It is important to note that some employers may have their own age requirements that exceed the minimum legal age. Additionally, some endorsements for a CDL (such as passenger transport or hazardous materials) may also have age requirements that exceed the minimum legal age. It is important to check with your state's Department of Motor Vehicles and any potential employers to determine the specific age requirements for your desired type of driving.
The endorsements required for a Class A CDL license depend on the type of driving you plan to do.
The following are some of the common endorsements for a Class A CDL:
1. Doubles/Triples (T) Endorsement: Required to drive vehicles with multiple trailers, such as double or triple trailers.
2. Tanker (N) Endorsement: Required to drive vehicles designed to transport liquids or gases in bulk containers.
3. Hazardous Materials (H) Endorsement: Required to transport hazardous materials as defined by the Department of Transportation.
4. Passenger (P) Endorsement: Required to transport passengers in a commercial vehicle, such as a bus.
To obtain an endorsement, you will need to pass a written knowledge test and any additional skills test required for that endorsement. You will also need to meet any additional requirements, such as specific age or experience requirements. It is important to check with your state's Department of Motor Vehicles for specific information on obtaining endorsements for a Class A CDL license.
The following are some of the common endorsements for a Class A CDL:
1. Doubles/Triples (T) Endorsement: Required to drive vehicles with multiple trailers, such as double or triple trailers.
2. Tanker (N) Endorsement: Required to drive vehicles designed to transport liquids or gases in bulk containers.
3. Hazardous Materials (H) Endorsement: Required to transport hazardous materials as defined by the Department of Transportation.
4. Passenger (P) Endorsement: Required to transport passengers in a commercial vehicle, such as a bus.
To obtain an endorsement, you will need to pass a written knowledge test and any additional skills test required for that endorsement. You will also need to meet any additional requirements, such as specific age or experience requirements. It is important to check with your state's Department of Motor Vehicles for specific information on obtaining endorsements for a Class A CDL license.
The Class A CDL skills test is designed to assess your ability to safely operate a commercial motor vehicle. It consists of three parts: the pre-trip inspection, the basic vehicle control skills test, and the on-road driving test.
1. Pre-trip inspection: This portion of the test requires you to show that you can inspect your vehicle to ensure that it is safe to operate. You will need to identify and explain the items you are inspecting, such as brakes, suspension, lights, and tires.
2. Basic vehicle control skills test: This portion of the test requires you to show that you can safely maneuver your vehicle in a controlled environment. You will need to perform several maneuvers, such as straight line backing, offset backing, and parallel parking.
3. On-road driving test: This portion of the test requires you to demonstrate your ability to safely operate your vehicle on public roads. You will need to navigate through traffic and demonstrate your ability to perform basic driving maneuvers, such as turning and merging.
It is important to note that specific requirements for the skills test may vary depending on the state where you are taking the test. It is recommended that you check with your state's Department of Motor Vehicles for specific information on the Class A CDL skills test in your area.
1. Pre-trip inspection: This portion of the test requires you to show that you can inspect your vehicle to ensure that it is safe to operate. You will need to identify and explain the items you are inspecting, such as brakes, suspension, lights, and tires.
2. Basic vehicle control skills test: This portion of the test requires you to show that you can safely maneuver your vehicle in a controlled environment. You will need to perform several maneuvers, such as straight line backing, offset backing, and parallel parking.
3. On-road driving test: This portion of the test requires you to demonstrate your ability to safely operate your vehicle on public roads. You will need to navigate through traffic and demonstrate your ability to perform basic driving maneuvers, such as turning and merging.
It is important to note that specific requirements for the skills test may vary depending on the state where you are taking the test. It is recommended that you check with your state's Department of Motor Vehicles for specific information on the Class A CDL skills test in your area.
Yes, there are restrictions and limitations for drivers with a Class A CDL license. Some of the common restrictions and limitations include:
1. Air brake restriction: If you do not pass the air brake knowledge test or fail to demonstrate proficiency in operating a vehicle with air brakes during the skills test, you may be restricted from operating vehicles with air brakes.
2. Automatic transmission restriction: If you take the skills test in a vehicle with an automatic transmission, you will be restricted from operating vehicles with manual transmissions.
3. Hazardous materials endorsement restriction: If you do not pass the hazardous materials knowledge test or do not meet other requirements for the endorsement, you will be restricted from transporting hazardous materials.
4. Passenger endorsement restriction: If you do not pass the passenger endorsement knowledge test or do not meet other requirements for the endorsement, you will be restricted from transporting passengers.
It is important to note that restrictions and limitations may vary depending on the state where you obtained your CDL license. It is recommended that you check with your state's Department of Motor Vehicles for specific information on restrictions and limitations for drivers with a Class A CDL license in your area.
1. Air brake restriction: If you do not pass the air brake knowledge test or fail to demonstrate proficiency in operating a vehicle with air brakes during the skills test, you may be restricted from operating vehicles with air brakes.
2. Automatic transmission restriction: If you take the skills test in a vehicle with an automatic transmission, you will be restricted from operating vehicles with manual transmissions.
3. Hazardous materials endorsement restriction: If you do not pass the hazardous materials knowledge test or do not meet other requirements for the endorsement, you will be restricted from transporting hazardous materials.
4. Passenger endorsement restriction: If you do not pass the passenger endorsement knowledge test or do not meet other requirements for the endorsement, you will be restricted from transporting passengers.
It is important to note that restrictions and limitations may vary depending on the state where you obtained your CDL license. It is recommended that you check with your state's Department of Motor Vehicles for specific information on restrictions and limitations for drivers with a Class A CDL license in your area.
It depends on the individual state's policies and regulations on language translations for CDL exams. In Oklahoma, for example, the CDL written test is only available in English and the applicant must be able to read and write in English. However, some states may offer the CDL written test in other languages or provide an interpreter if necessary. It is recommended that you check with your state's Department of Motor Vehicles for specific information on language translations for CDL exams in your area.
Yes, you can request accommodations for the Class A CDL written test due to a disability. Under the Americans with Disabilities Act (ADA), the Department of Motor Vehicles (DMV) is required to provide reasonable accommodations to individuals with disabilities taking the CDL exam.
To request accommodations, you will need to contact your state's DMV and provide documentation of your disability and the accommodations you are requesting. The DMV will review your request and determine if the accommodations are reasonable and appropriate.
Some examples of accommodations that may be provided include extra time to complete the exam, a reader or scribe, or a separate testing room. It is important to make your request for accommodations well in advance of your scheduled exam date, as the DMV may need time to arrange for the necessary accommodations.
Remember that each state has its own policies and procedures for requesting accommodations, so it's important to contact your state's DMV for specific information on how to request accommodations for the CDL written test.
To request accommodations, you will need to contact your state's DMV and provide documentation of your disability and the accommodations you are requesting. The DMV will review your request and determine if the accommodations are reasonable and appropriate.
Some examples of accommodations that may be provided include extra time to complete the exam, a reader or scribe, or a separate testing room. It is important to make your request for accommodations well in advance of your scheduled exam date, as the DMV may need time to arrange for the necessary accommodations.
Remember that each state has its own policies and procedures for requesting accommodations, so it's important to contact your state's DMV for specific information on how to request accommodations for the CDL written test.
If you fail the Class A CDL written test, you will be allowed to retake the test after a certain waiting period. In Oklahoma, for example, you are allowed to retake the test the next business day.
The waiting period between retakes may vary depending on your state's policies. It is important to note that there may be a maximum number of times you can retake the test within a certain period of time.
If you fail the written test multiple times, you may be required to complete additional training or education before being allowed to retake the test again. It is important to review the study materials and practice tests before retaking the exam to increase your chances of passing.
Be sure to follow your state's specific policies and procedures for retaking the CDL written exam.
The waiting period between retakes may vary depending on your state's policies. It is important to note that there may be a maximum number of times you can retake the test within a certain period of time.
If you fail the written test multiple times, you may be required to complete additional training or education before being allowed to retake the test again. It is important to review the study materials and practice tests before retaking the exam to increase your chances of passing.
Be sure to follow your state's specific policies and procedures for retaking the CDL written exam.
