Knowledge Test Class B
This license is required for driving a single vehicle with a GVWR of more than 26,001 pounds, and a trailer not to exceed 10,000 pounds gross vehicle weight rating, or a vehicle designed to transport 24 or more people (including the driver). To receive this license, applicants must pass a 50-question test. To pass, applicants must answer 40 questions correctly. Each question has two, three or four possible answer choices. Test questions come from the Utah Commercial Driver License Handbook. Questions come from chapters covering: Introduction, Driving Safely, Transporting Cargo Safely, Air Brakes (if applicable), Pre-Trip Vehicle Inspection Test, Basic Vehicle Control Skills Test and On-Road Driving.. Endorsements that may be used with a Class B CDL are: Hazardous materials, Tank, Passenger, HazMat and Tank, Air Brakes and School bus.
Number of Question
Passing Score
1. Aggressive driving is:
Explanation
Aggressive driving is the act of operating a motor vehicle in a selfish, bold, or pushy manner and without regard for the rights or safety of other road users.
2. A fire extinguisher is a required piece of safety equipment.
Explanation
When inspecting a vehicle, you should check for required emergency equipment, including at least one fire extinguisher.
3. What is the purpose of a vehicle inspection report?
Explanation
A vehicle inspection report allows a driver to inform the motor carrier of issues that could affect the safe operation of a vehicle. If required, the driver should fill out a vehicle inspection report after every day of driving. They should make note of any issues that could affect the safety of the vehicle or that could lead to a mechanical breakdown.
4. Hydroplaning:
Explanation
Hydroplaning is an effect in which a vehicle's tires lose traction with the surface of the road and instead glide along a layer of water. There does not have to be a large amount of water on the road for this to occur. Hydroplaning can begin at speeds as low as 30 mph.
5. A cargo cover that flaps in transit:
Explanation
Cargo covers should not flap in the wind. A flapping cover could tear loose entirely, exposing the cargo, and potentially blocking your view or the view of other drivers.
6. When traveling long distances, you should:
Explanation
To avoid becoming fatigued on a long trip, you should take a break after every 100 miles or two hours of driving. Driving through the night, or during any other time when you would normally be asleep, raises the danger of fatigue.
7. Backing with a trailer is dangerous because:
Explanation
Backing a truck is always dangerous because the driver may not be able to see everything behind them. CMV operators should avoid backing whenever possible.
Ranked by best match
Frequently Asked Questions
A Class B CDL (Commercial Driver's License) in Utah is a type of license that allows the holder to operate a single vehicle with a weight of 26,001 pounds or more, or a combination of vehicles with a total weight of less than 26,001 pounds, but with a towed vehicle that weighs more than 10,000 pounds.
Step-by-step process to obtain a Class B CDL license in Utah:
1. Meet the eligibility requirements:
- Be at least 18 years old (21 years old for interstate operation)
- Hold a valid Utah driver's license
- Have a clean driving record
- Pass a medical examination and obtain a medical certificate
- Provide proof of residency and legal presence in the United States
2. Obtain and study the Utah CDL Handbook:
- The handbook contains all the necessary information regarding the exam and requirements for obtaining a Class B CDL.
3. Complete and submit an application to obtain a CDL learner's permit:
- You can obtain an application online or from any Utah driver's license office.
- You will be required to pay an application fee.
4. Pass the written knowledge test:
- The knowledge test covers general driving knowledge and specific information related to operating a commercial vehicle.
- You must achieve a score of at least 80% to pass.
5. Obtain your CDL learner's permit:
- Once you pass the written knowledge test, you will be issued a CDL learner's permit.
- You must hold your learner's permit for at least 14 days before taking the skills test.
6. Practice driving with your learner's permit:
- You must practice driving with your learner's permit while accompanied by another licensed CDL holder.
7. Schedule and pass the skills test:
- The skills test consists of three parts: a pre-trip vehicle inspection, a basic control skills test, and an on-road driving test.
- You must pass all three parts to obtain your Class B CDL.
8. Pay the required fees:
- Once you pass the skills test, you will be required to pay the required fees to obtain your Class B CDL.
Note: It is important to keep in mind that the process may vary slightly depending on individual circumstances and any changes in state regulations.
Step-by-step process to obtain a Class B CDL license in Utah:
1. Meet the eligibility requirements:
- Be at least 18 years old (21 years old for interstate operation)
- Hold a valid Utah driver's license
- Have a clean driving record
- Pass a medical examination and obtain a medical certificate
- Provide proof of residency and legal presence in the United States
2. Obtain and study the Utah CDL Handbook:
- The handbook contains all the necessary information regarding the exam and requirements for obtaining a Class B CDL.
3. Complete and submit an application to obtain a CDL learner's permit:
- You can obtain an application online or from any Utah driver's license office.
- You will be required to pay an application fee.
4. Pass the written knowledge test:
- The knowledge test covers general driving knowledge and specific information related to operating a commercial vehicle.
- You must achieve a score of at least 80% to pass.
5. Obtain your CDL learner's permit:
- Once you pass the written knowledge test, you will be issued a CDL learner's permit.
- You must hold your learner's permit for at least 14 days before taking the skills test.
6. Practice driving with your learner's permit:
- You must practice driving with your learner's permit while accompanied by another licensed CDL holder.
7. Schedule and pass the skills test:
- The skills test consists of three parts: a pre-trip vehicle inspection, a basic control skills test, and an on-road driving test.
- You must pass all three parts to obtain your Class B CDL.
8. Pay the required fees:
- Once you pass the skills test, you will be required to pay the required fees to obtain your Class B CDL.
Note: It is important to keep in mind that the process may vary slightly depending on individual circumstances and any changes in state regulations.
With a Class B CDL license in Utah, you can operate a single vehicle with a gross vehicle weight rating (GVWR) of 26,001 pounds or more. You can also operate a combination of vehicles, such as a truck and trailer, with a combined GVWR of less than 26,001 pounds, but the trailer being towed weighs more than 10,000 pounds.
Some examples of vehicles you can operate with a Class B CDL license include:
- Straight trucks
- Large buses (e.g. school buses)
- Dump trucks
- Cement mixers
- Tow trucks
- Delivery trucks
- Box trucks
It is important to note that some vehicles may require additional endorsements or specialized training to operate legally. Be sure to check Utah's CDL regulations for specific requirements and restrictions on certain vehicles.
Some examples of vehicles you can operate with a Class B CDL license include:
- Straight trucks
- Large buses (e.g. school buses)
- Dump trucks
- Cement mixers
- Tow trucks
- Delivery trucks
- Box trucks
It is important to note that some vehicles may require additional endorsements or specialized training to operate legally. Be sure to check Utah's CDL regulations for specific requirements and restrictions on certain vehicles.
To obtain a Class B CDL (Commercial Driver's License) license in Utah, you must meet the following requirements:
1. Age Requirements:
- You must be at least 18 years old to operate a commercial vehicle within Utah state boundaries.
- You must be at least 21 years old to operate a commercial vehicle across state lines or transport hazardous materials.
2. Valid Driver's License:
- You must already have a valid Utah driver's license.
3. Medical Certification:
- You must pass a medical examination and obtain a medical certificate from a certified medical examiner.
4. Residency:
- You must provide proof of residency and legal presence in the United States.
5. Knowledge Test:
- You must pass the CDL written knowledge test, which includes general driving knowledge and specific information related to operating commercial vehicles.
6. Skills Test:
- You must pass the CDL skills test, which includes three parts: pre-trip vehicle inspection, basic control skills test, and on-road driving test.
7. Background Check:
- You will be required to undergo a criminal background check.
Note: These requirements may vary depending on individual circumstances and any changes in state regulations. Be sure to check Utah's CDL regulations for specific requirements and restrictions on certain vehicles.
1. Age Requirements:
- You must be at least 18 years old to operate a commercial vehicle within Utah state boundaries.
- You must be at least 21 years old to operate a commercial vehicle across state lines or transport hazardous materials.
2. Valid Driver's License:
- You must already have a valid Utah driver's license.
3. Medical Certification:
- You must pass a medical examination and obtain a medical certificate from a certified medical examiner.
4. Residency:
- You must provide proof of residency and legal presence in the United States.
5. Knowledge Test:
- You must pass the CDL written knowledge test, which includes general driving knowledge and specific information related to operating commercial vehicles.
6. Skills Test:
- You must pass the CDL skills test, which includes three parts: pre-trip vehicle inspection, basic control skills test, and on-road driving test.
7. Background Check:
- You will be required to undergo a criminal background check.
Note: These requirements may vary depending on individual circumstances and any changes in state regulations. Be sure to check Utah's CDL regulations for specific requirements and restrictions on certain vehicles.
In Utah, you must be at least 18 years old to obtain a Class B CDL (Commercial Driver's License) license. However, if you plan to operate a commercial vehicle across state lines or transport hazardous materials, you must be at least 21 years old.
It is important to note that some employers may have their own age requirements for certain positions or types of commercial vehicles. Additionally, some driving schools may have their own age requirements for enrollment in their CDL training programs. Be sure to check with your employer or driving school for any additional age requirements that may apply.
It is important to note that some employers may have their own age requirements for certain positions or types of commercial vehicles. Additionally, some driving schools may have their own age requirements for enrollment in their CDL training programs. Be sure to check with your employer or driving school for any additional age requirements that may apply.
Yes, you may need certain endorsements for a Class B CDL (Commercial Driver's License) license in Utah depending on the type of vehicle you plan to operate and the cargo you plan to transport.
The following are the endorsements that are available for a Class B CDL license in Utah:
1. Passenger (P) Endorsement - Required if you plan to transport more than 15 passengers, including the driver.
2. School Bus (S) Endorsement - Required if you plan to drive a school bus that carries passengers.
3. Tank Vehicles (N) Endorsement - Required if you plan to transport liquids or gases in bulk containers with a capacity of 1,000 gallons or more.
4. Hazardous Materials (H) Endorsement - Required if you plan to transport hazardous materials, as defined by federal law.
5. Combination Tank and Hazardous Materials (X) Endorsement - Required if you plan to transport both hazardous materials and liquids or gases in bulk containers with a capacity of 1,000 gallons or more.
To obtain an endorsement, you must pass additional knowledge and skills tests that are specific to the endorsement type. You may also need to meet additional requirements, such as obtaining a Transportation Security Administration (TSA) clearance for the Hazardous Materials endorsement.
Note: These requirements may vary depending on individual circumstances and any changes in state regulations. Be sure to check Utah's CDL regulations for specific endorsement requirements that may apply to your situation.
The following are the endorsements that are available for a Class B CDL license in Utah:
1. Passenger (P) Endorsement - Required if you plan to transport more than 15 passengers, including the driver.
2. School Bus (S) Endorsement - Required if you plan to drive a school bus that carries passengers.
3. Tank Vehicles (N) Endorsement - Required if you plan to transport liquids or gases in bulk containers with a capacity of 1,000 gallons or more.
4. Hazardous Materials (H) Endorsement - Required if you plan to transport hazardous materials, as defined by federal law.
5. Combination Tank and Hazardous Materials (X) Endorsement - Required if you plan to transport both hazardous materials and liquids or gases in bulk containers with a capacity of 1,000 gallons or more.
To obtain an endorsement, you must pass additional knowledge and skills tests that are specific to the endorsement type. You may also need to meet additional requirements, such as obtaining a Transportation Security Administration (TSA) clearance for the Hazardous Materials endorsement.
Note: These requirements may vary depending on individual circumstances and any changes in state regulations. Be sure to check Utah's CDL regulations for specific endorsement requirements that may apply to your situation.
The Class B CDL (Commercial Driver's License) skills test in Utah consists of three parts:
1. Pre-Trip Vehicle Inspection - You will be required to do a thorough inspection of your vehicle to ensure that it is safe to operate. This includes checking the engine compartment, the coupling system, and the lights and reflectors, among other things.
2. Basic Vehicle Control - You will be tested on your ability to control the vehicle in different situations, such as backing up, turning, and parking.
3. On-Road Driving - You will be required to demonstrate your ability to drive safely in different traffic situations, such as changing lanes, merging onto a highway, and making turns.
To pass the skills test, you must complete each part of the test within a certain timeframe and meet certain minimum score requirements. You must also demonstrate safe driving practices throughout the entire test.
It is important to note that the skills test is just one part of the CDL licensing process. You must also pass a written knowledge test and meet other requirements before you can obtain your Class B CDL license in Utah.
1. Pre-Trip Vehicle Inspection - You will be required to do a thorough inspection of your vehicle to ensure that it is safe to operate. This includes checking the engine compartment, the coupling system, and the lights and reflectors, among other things.
2. Basic Vehicle Control - You will be tested on your ability to control the vehicle in different situations, such as backing up, turning, and parking.
3. On-Road Driving - You will be required to demonstrate your ability to drive safely in different traffic situations, such as changing lanes, merging onto a highway, and making turns.
To pass the skills test, you must complete each part of the test within a certain timeframe and meet certain minimum score requirements. You must also demonstrate safe driving practices throughout the entire test.
It is important to note that the skills test is just one part of the CDL licensing process. You must also pass a written knowledge test and meet other requirements before you can obtain your Class B CDL license in Utah.
Yes, there are certain restrictions and limitations for drivers with a Class B CDL (Commercial Driver's License) license in Utah. These restrictions are in place to ensure the safety of the driver and other road users.
The following are some common restrictions and limitations for Class B CDL drivers in Utah:
1. Vehicle Weight - If you obtain a Class B CDL license with a restriction, you may be limited to operating vehicles with a certain weight or number of axles.
2. Passenger Restrictions - If you obtain a Class B CDL with a passenger endorsement, you may be restricted from carrying passengers for hire.
3. Hazardous Materials Restrictions - If you obtain a Class B CDL with a hazardous materials endorsement, you may be restricted from transporting certain types of hazardous materials or limited to transporting hazardous materials within a certain distance or area.
4. Air Brake Restrictions - If you do not pass the air brake knowledge and skills test, you may be restricted from operating vehicles equipped with air brakes.
5. Time Restrictions - If you are under 21 years of age, you may be restricted from driving commercial vehicles across state lines or during certain hours.
It is important to familiarize yourself with any restrictions or limitations that apply to your particular situation. Violating these restrictions can result in fines, penalties, or even the suspension or revocation of your CDL license.
The following are some common restrictions and limitations for Class B CDL drivers in Utah:
1. Vehicle Weight - If you obtain a Class B CDL license with a restriction, you may be limited to operating vehicles with a certain weight or number of axles.
2. Passenger Restrictions - If you obtain a Class B CDL with a passenger endorsement, you may be restricted from carrying passengers for hire.
3. Hazardous Materials Restrictions - If you obtain a Class B CDL with a hazardous materials endorsement, you may be restricted from transporting certain types of hazardous materials or limited to transporting hazardous materials within a certain distance or area.
4. Air Brake Restrictions - If you do not pass the air brake knowledge and skills test, you may be restricted from operating vehicles equipped with air brakes.
5. Time Restrictions - If you are under 21 years of age, you may be restricted from driving commercial vehicles across state lines or during certain hours.
It is important to familiarize yourself with any restrictions or limitations that apply to your particular situation. Violating these restrictions can result in fines, penalties, or even the suspension or revocation of your CDL license.
Yes, you can take the Class B CDL (Commercial Driver's License) written test in Utah in a language other than English. The Utah Driver License Division offers the written test in several languages, including Spanish, Chinese, Russian, and French.
To take the test in a language other than English, you must first make an appointment with the Driver License Division and indicate your preferred language. You will need to provide identification documents and pay the testing fee. The test will be administered using an interpreter or through a computer-based testing system that offers translations.
It is important to note that even if you take the written test in a language other than English, you will still need to demonstrate your ability to communicate in English when taking the skills test. This is because English is the primary language used on the road and is essential for communicating with other drivers, law enforcement, and emergency services personnel.
To take the test in a language other than English, you must first make an appointment with the Driver License Division and indicate your preferred language. You will need to provide identification documents and pay the testing fee. The test will be administered using an interpreter or through a computer-based testing system that offers translations.
It is important to note that even if you take the written test in a language other than English, you will still need to demonstrate your ability to communicate in English when taking the skills test. This is because English is the primary language used on the road and is essential for communicating with other drivers, law enforcement, and emergency services personnel.
Yes, you can request accommodations for the Class B CDL (Commercial Driver's License) written test in Utah if you have a disability that affects your ability to take the test. The Utah Driver License Division provides accommodations for individuals with disabilities to ensure that they have an equal opportunity to obtain a CDL license.
To request accommodations, you must first make an appointment with the Driver License Division and inform them of your disability and the specific accommodations that you require. The Division may require documentation of your disability and a description of the accommodations that you need.
Some examples of accommodations that may be provided include extra time to complete the test, a separate testing room, a reader or scribe, or assistive technology such as screen readers or magnifiers.
It is important to make your accommodation request well in advance of your scheduled test date to ensure that the necessary arrangements can be made. The Driver License Division will work with you to determine the appropriate accommodations based on your individual needs.
To request accommodations, you must first make an appointment with the Driver License Division and inform them of your disability and the specific accommodations that you require. The Division may require documentation of your disability and a description of the accommodations that you need.
Some examples of accommodations that may be provided include extra time to complete the test, a separate testing room, a reader or scribe, or assistive technology such as screen readers or magnifiers.
It is important to make your accommodation request well in advance of your scheduled test date to ensure that the necessary arrangements can be made. The Driver License Division will work with you to determine the appropriate accommodations based on your individual needs.
If you fail the Class B CDL (Commercial Driver's License) written test in Utah, you are allowed to retake the test. However, you will need to wait at least one day before attempting to retake the test. You will need to pay the testing fee again when you retake the test.
It is important to note that there is a limit to the number of times you can take the written test in a single day. The Utah Driver License Division allows you to take up to three tests in one day, but if you fail all three tests, you will need to wait at least three days before attempting to retake them.
If you fail the written test multiple times, it may be helpful to take a commercial driver's license course or study materials to better prepare for the exam. Additionally, it may be beneficial to schedule a retest after sufficient time has passed to ensure that you have had enough time to study and prepare for the exam again.
It is important to note that there is a limit to the number of times you can take the written test in a single day. The Utah Driver License Division allows you to take up to three tests in one day, but if you fail all three tests, you will need to wait at least three days before attempting to retake them.
If you fail the written test multiple times, it may be helpful to take a commercial driver's license course or study materials to better prepare for the exam. Additionally, it may be beneficial to schedule a retest after sufficient time has passed to ensure that you have had enough time to study and prepare for the exam again.
